1 1

TEST FT-VC-DTS-ETH-250M-2

TEST FT-VC-DTS-ETH-250M-2

View full details
Product Overview

The FT-VC-DTS-ETH-250M-2 network interface high-speed acquisition card belongs to the series of high-speed DAQ acquisition cards specifically designed for weak signal acquisition, developed for the distributed Raman DTS optical temperature measurement system, and also compatible with the acquisition of weak echo signals from aerosol lidar. It features dual channels of 12-bit ADC, supporting software switching between 100 MSps and 250 MSps sampling rates, suitable for projects with different distances and spatial resolutions; it includes a hardware accumulation averaging algorithm, capable of up to 65,536 accumulations to amplify weak Raman signals, significantly reducing noise; it supports TTL external triggering for optical path synchronization and low-latency transmission via Gigabit network interface UDP; the board is available in two versions: bare board FT-VC-DTS-ETH-250M-2 and with a casing FT-VC-DTS-ETH-250M-2A. It is small in size, low in power consumption at 12V, and is the preferred acquisition hardware for DTS equipment manufacturers as OEM, for university research on Raman temperature measurement, and for the development of aerosol radar.

Core product advantages

● Sampling rate can be set to 100 MSps or 250 MSps
● 12-bit dual-channel synchronous real-time sampling
● Supports trigger input sampling (TTL 3.3 - 5V) / trigger output (TTL 3.3V)
● Gigabit network port, UDP transmission protocol
● ±2.0V input range (customizable)
● Built-in averaging algorithm, maximum averaging times up to 65536 times
● Each channel supports up to 32768 points

Application scenario

●  Complete OEM kits of DTS optical fiber temperature measurement hosts for power cables, pipe galleries and tunnels

●  Hardware for distributed Raman temperature monitoring system of oil and gas storage tanks and oil pipelines

●  Temperature monitoring equipment acquisition units for high-temperature fires in coal mines and chemical storage warehouses

●  Raman DTS temperature measurement algorithms and aerosol laser radar research experimental platform for universities

●  Embedded acquisition hardware for small portable optical fiber temperature measurement inspection instruments

Complete hardware specification parameter comparison table

Parameter FT‑VC‑DTS‑ETH‑250M‑2 Remarks
Number of Input Channels 2 2‑channel synchronous sampling
Resolution 12 bits
Sampling Rate 100M/250M Switchable via interface call
Sampling Points ≤32768 100M sampling: covers 32 km optical cable;

250M sampling: covers 13 km optical cable
Built‑in Averaging ≤65536 times Configurable times
Trigger Input for Sampling TTL 3.3‑5V Trigger output (TTL 3.3V) is optional
Input Voltage Range ±2.0V (Customizable)
Input Coupling Mode DC coupling 50‑ohm input impedance
Communication Interface & Protocol RJ45 Gigabit Ethernet, UDP protocol
Power Supply 12V/0.6A
Operating Temperature -20~60℃
Mechanical Dimension 105mm(L) × 90mm(W)

 

 


Professor Wu from F-tone Networks was selected as one of the top 2% global scientists for four consecutive years from 2022 to 2025 (https://elsevier.digitalcommonsdata.com/datasets/btchxktzyw/6)

F-tone Networks Technical Support:

Email:una@f-tone.com

WhatsApp and WeChat: +86177 6116 3895

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.

HFBR-1414TZ | HFBR-2412TZ AVAGO compatible full series

View all

HFBR-1521Z | HFBR-2521Z | AFBR-1629Z | HFBR-2629Z AVAGO compatible full series

View all

Power and Wavelength Testing

Test the signal delivering strength and wavelength, to ensure the signal decoding capacity of the receiver, and the wavelength remains consistent from the transmitter to the receiver.

Power and Wavelength Testing

Traffic Testing

Test the bit error rate and packet loss rate, to make them meet the corresponding standards and ensure the performance of transceivers.

Traffic Testing

Optical Performance Testing

Test the transceivers' eye diagram situation, receiving sensitivity, extinction ratio, wavelength, light-emitting, light-receiving, current and voltage, to ensure the signal quality, stability and reliability of the transmission.

Optical Performance Testing

End Face Testing

Check the end face of the transceivers and keep them clean for more stable data transmission, better performance, and durability.

End Face Testing

Various Switch Tests

Every module is quality tested for compatibility in the multi-brand switches environment, guaranteeing flawless operations.

Various Switch Tests

About F-tone Networks

F-tone Networks is now a world leader in development of optical transceivers and provide a wide range of high-speed optical solutions for optical communication networking, especially for AI, Data Center, enterprise data networking, Industry, aerospace, mining, shipbuilding, railway, metro, long haul transport networking, and mobile access networking applications
F-tone Networks invested in foundational photonics technologies and extensive product development and engineering with global presence in many area also.

about usContact Us